5083 aluminum circle disc

161 Views 2024-01-17 07:51:39

Product 5083 aluminum circle
Thickness 0.3~10mm, customize;
Diameter 100mm – 1500mm, customize
Application Road sign, Lamp shade, Pan Lid, Kettle, Induction Cooker Cladding, etc.
Price terms FOB, CRF, CIF
Delivery Time 30 DAYS
Whatsapp E-mail Contact

5083 aluminum circle disc introduction

5083 aluminum circle have higher strength than 5052 aluminum and has exceptional thermal conductivity. In the tempered condition, it retains good formability due to excellent ductility. It is highly suitable for welding and can be hardened by cold work.

5083 aluminum circle

5083 aluminum circle

5083 aluminum circle is stamped from 5083 aluminum coil, and its performance is basically the same as 5083 aluminum plate/coil.

Composition Specification Of 5083 Aluminum Circle

Alloy Si Fe Cu Mn Mg Cr Zn Ti Others
5083 0.40 0.40 0.10 0.40-1.0 4.0-4.9 0.05-0.25 0.25 0.15 0.15

Grade Specification Comparison

Alloy UNS(No) ISO BS DIN
5083 A95083 AlMg4.5Mn N8 AlMg4.5Mn
These comparisons are approximate only. The list is intended as a comparison of functionally similar
materials not as a schedule of contractual equivalents. If exact equivalents are needed original specifications
must be consulted.

Mechanical Properties Of 5083 Aluminum Circle

Yield Tensile Strength 210 MPa
Ultimate Tensile Strength 300 MPa
Tensile Modulus 72 GPa
Shear Strength 175 MPa
Shear Modulus 26 GPa
Fatigue Strength 150 MPa
Elongation At Break 22 %
Poisson’s Ratio 0.33
Hardness B77/87
Density 2.7 g/cm³

Application of 5083 aluminum circle discs

Deep drawing products: The good formability and deep drawing performance of 5083 aluminium alloy enable it to be processed into complex thin-walled containers or other deep drawing products.

Application of anodized 5083 aluminum discs

Application of anodized 5083 aluminum discs

Traffic signs: As the mentioned information on aluminum plates for traffic signs in Zhejiang shows, 5083 aluminum plates are suitable for making traffic signs, street signs, etc. due to their corrosion resistance and outdoor durability.

Anodizing use: After anodizing, the 5083 aluminum disc has a beautiful surface and further enhances corrosion resistance. It is suitable for high-end decoration and electronic product casings or components.

High-end pressure cooker: 5083 aluminium circle discs have excellent performance, are very suitable for pressure vessels and have excellent deep drawing performance.

Pressure cooker

Pressure cooker

Chemical containers: 5083 aluminum circle discs have strong corrosion resistance, are very suitable as chemical container materials, and have excellent deep drawing properties.

Although 5083 aluminum circles have outstanding performance, their prices are much higher than 1000 series aluminum wafers. Therefore, 1000 series aluminum wafers are more commonly seen in daily applications, such as:

5083 aluminum discs are expensive and are generally used in pressure cooker manufacturing or applications with special requirements.

Casting production process and its introduction

The purpose of melting and casting is to produce alloys with satisfactory composition and high purity of melt, so as to create favorable conditions for casting alloys of various shapes.

Melting and casting process steps: batching --- feeding --- melting --- stirring after melting, slag removal --- pre-analysis sampling --- adding alloy to adjust the composition, stirring --- refining --- static Setting——Guide furnace casting.

Hot rolling production process and its introduction

  • 1. Hot rolling generally refers to rolling above the metal recrystallization temperature;
  • 2. During the hot rolling process, the metal has both hardening and softening processes. Due to the influence of deformation speed, as long as the recovery and recrystallization process is too late, there will be a certain work hardening;
  • 3. The recrystallization of the metal after hot rolling is incomplete, that is, the coexistence of recrystallized structure and deformed structure;
  • 4. Hot rolling can improve the processing performance of metals and alloys, reduce or eliminate casting defects.
    • Hot rolling equipment

      Casting and rolling process

      Casting and rolling process: liquid metal, front box (liquid level control), casting and rolling machine (lubrication system, cooling water), shearing machine, coiling machine.

      • 1. The casting and rolling temperature is generally between 680°C and 700°C. The lower the better, the stable casting and rolling line usually stops once a month or more to re-stand. During the production process, it is necessary to strictly control the liquid level of the front tank to prevent low liquid level;
      • 2. Lubrication uses C powder with incomplete combustion of gas for lubrication, which is also one of the reasons for the dirty surface of casting and rolling materials;
      • 3. The production speed is generally between 1.5m/min-2.5m/min;
      • 4. The surface quality of products produced by casting and rolling is generally relatively low, and generally cannot meet products with special physical and chemical performance requirements.
        • Cold rolling production process

          • 1. Cold rolling refers to the rolling production method below the recrystallization temperature;
          • 2. There will be no dynamic recrystallization during the rolling process, and the temperature will rise to the recovery temperature at most, and the cold rolling will appear in a work hardening state, and the work hardening rate will be large;
          • 3. The cold-rolled sheet and strip have high dimensional accuracy, good surface quality, uniform structure and performance, and products in various states can be obtained with heat treatment;
          • 4. Cold rolling can roll out thin strips, but at the same time, it has the disadvantages of high energy consumption for deformation and many processing passes.
            • Casting rolling

              Introduction to finishing production process

              • 1. Finishing is a processing method to make the cold-rolled sheet meet the customer's requirements, or to facilitate the subsequent processing of the product;
              • 2. The finishing equipment can correct the defects produced in the hot rolling and cold rolling production process, such as cracked edge, oily, poor plate shape, residual stress, etc. It needs to ensure that no other defects are brought into the production process;
              • 3. There are various finishing equipments, mainly including cross-cutting, slitting, stretching and straightening, annealing furnace, slitter, etc.

Aluminum alloy has the characteristics of low density, good mechanical properties, good processing performance, non-toxic, easy to recycle, excellent electrical conductivity, heat transfer and corrosion resistance, so it has a wide range of applications.

Aerospace: used to make aircraft skins, fuselage frames, girders, rotors, propellers, fuel tanks, wall panels and landing gear struts, as well as rocket forging rings, spacecraft wall panels, etc.

Aluminum alloy used for aerospace

Aluminum alloy used for aerospace

Transportation: used for car body structure materials of automobiles, subway vehicles, railway passenger cars, high-speed passenger cars, doors and windows, shelves, automotive engine parts, air conditioners, radiators, body panels, wheels and ship materials.

Traffic application

Traffic application

Packaging: All-aluminum pop cans are mainly used as metal packaging materials in the form of thin plates and foils, and are made into cans, lids, bottles, barrels, and packaging foils. Widely used in the packaging of beverages, food, cosmetics, medicines, cigarettes, industrial products, medicines, etc.

Packaging application

Packaging application

Printing: Mainly used to make PS plates, aluminum-based PS plates are a new type of material in the printing industry, used for automatic plate making and printing.

PS printing

PS printing

Architectural decoration: aluminum alloy is widely used in building structures, doors and windows, suspended ceilings, decorative surfaces, etc. due to its good corrosion resistance, sufficient strength, excellent process performance and welding performance.

Aluminum alloy construction application

Aluminum alloy construction application

Electronic products: computers, mobile phones, refrigerator shells, radiators, etc.

Electronic product application

Electronic product application

Kitchen supplies: aluminum pots, aluminum basins, rice cooker liners, household aluminum foil, etc.

Kitchen application

Kitchen application

Packaging Of Aluminum Sheet/Coil

Every detail of packaging is where we pursue perfect service. Our packaging process as a whole is as follows:

Lamination: clear film, blue film, micro-mucosal, high-mucosal, laser cutting film (2 brands, Novacell and Polyphem);

Protection: paper corner protectors, anti-pressure pads;

drying: desiccant;

Tray: fumigated harmless wooden tray, reusable iron tray;

Packing: Tic-tac-toe steel belt, or PVC packing belt;

Material Quality: Completely free from defects such as white rust, oil spots, rolling marks, edge damage, bends, dents, holes, break lines, scratches, etc., no coil set.

Port: Qingdao or other ports in China.

Lead time: 15-45 days.

What is 1060 pure aluminum sheet

Aluminum sheet/plate packaging process

What is 1060 pure aluminum sheet

Aluminum coil packaging process

F: Are you a manufacturer or a trader?

Q: We are a manufacturer, our factory is at No.3 Weier Road, Industrial Zone, Gongyi, Henan, China.

F: What is the MOQ for ordering the product?

Q: Our MOQ is 5 tons, and some special products will have a minimum order quantity of 1 or 2 tons.

F: How long is your lead time?

Q: Generally our lead time is about 30 days.

F: Do your products have quality assurance?

Q: Yes, if there is a quality problem with our products, we will compensate the customer until they are satisfied.



Latest Blogs

Aluminum ore

The development history of aluminum and aluminum alloys

Aluminum is named after the Latin word "alumen", which means "bitter earth" or "alum". The name was first proposed by Swedish chemist Jons Jakob Berzelius around 1825 to describe the properties of this metal oxide.

What are the common quality problems of aluminum plates?

What are the common quality problems of aluminum plates?

In the production process of aluminum plates and strips, it is very easy to have product quality problems due to incorrect operation of machinery, equipment or staff.

Aluminum alloys are classified based on heat treatment properties

Aluminum alloys are classified based on heat treatment properties

Different series of aluminum alloys have different properties. According to the heat treatment properties, aluminum alloy materials can be divided into two categories: heat-treatable alloys and non-heat-treatable alloys.

The applications of different alloys of aluminum

The applications of different alloys of aluminum

Different alloys of aluminum have different properties and can be adapted to different applications. The following are the applications of different alloys of aluminum


Get in touch with us

Address

No.52, Dongming Road,
Zhengzhou, Henan, China

Call Us

Tel:+86-371-66302886
Whatsapp:+8618137782032

Huawei Certificates

Trusted Aluminum Sheet/Coil, Aluminum Foil, Aluminum Strip, Aluminum Circle Manufacturer
We provide high quality products only


Whatsapp/Wechat
+8618137782032
whatsapp wechat

[email protected]